How to make the Light Up Igloo card


Thank you for purchasing a Della by Design craft kit. The video tutorial for this design is being broadcast live as part of the Christmas Craft Along in early December. If you can’t wait that long, here are the step by step instructions.

Let’s get crafting!

Instructions

Grab a cup of tea, let’s take some time out and enjoy making this card together. 

The Advanced kit will contain:

  1. 1 square card (white/kraft)
  2. 1 envelope 
  3. 1 blue square
  4. 1 silver rectangle
  5. 1 white/cream rectangle
  6. LED light system with 3 bulbs
  7. 2 stamped igloos
  8. 2 penguins,3 bulbs, ‘press here’ circle (white/cream)
  9. 3 bulbs (green)
  10. ‘Season’s Greetings’ (blue)
  11. foam sticky pads

For the Expert kit, you’ll have the card stock and stamps you need to stamp and create the list above.

You may also need some colouring pens/pencils, scissors, cello tape and glue, anything suitable for paper and card – a glue stick or PVA glue. For the LED lights, you’ll need a 3V CR2016 battery (not included).

  1. Let’s start by colouring in the penguins and all the Christmas lights on the igloo (the one with holes) and the lights on the entrance on the other igloo.
  2. Next, we’ll cut out all the pieces we need – the penguins, the green bulbs/trees, the igloo (with holes) and the ‘PRESS HERE’ circle.
  3. For the other igloo, cut out the entrance arch only and cut away the bulb on the top. The white/cream bulbs can be cut out to look like snow on the green trees. Glue the snow directly onto the trees and stick foam pads to the back of the arch and attach to the igloo.
  4. We’re going to use the large white/cream rectangle to make 2 snowy hills. Cut a wavy line across the middle of the card – dividing the longest side into two. One half will be the hill in the foreground, cut the second hill from the remaining card – make sure the width is still 4.5inch. Top Tip – the hill in the background doesn’t need to reach the bottom of the card – it just needs to be hidden behind the front hill.
  5. Using the silver card as the sky, arrange the hills onto the large blue square. Place the igloo on top and adjust the hills until you’re happy with the layout and the igloo covers the join with the two hills.
  6. Carefully remove the igloo and draw a rough square of where it was positioned (1.5 x 1.5inches). Remove the top hill and cut away this square. Reposition and draw the opening onto the next layer. Repeat this for each layer, including the blue square. Top Tip – use a craft knife to cut a square through the blue square.
  7. Put the igloo to one side and arrange the hills, sky and trees. Once you’re happy with the layout, remove the larger trees and gently curve them on a wooden spoon handle. Add a thin foam pad along the tree. Add foam pads to the back of the hill in the foreground – left, right and the bottom so that the opening is clear.
  8. Glue the sky, hills and trees onto the blue square. You should have a hole going all the way through these layers.
  9. First, let’s test out the lights with 3V CR2016 battery (not included). Slot the battery into the silver pocket and click the orange button to test. If this doesn’t work, make sure the battery is the correct way up and doesn’t have a protective sticker to remove (I speak from experience!)
  10. Cut some cello tape pieces to have handy and then post each bulb into the holes on the igloo. I’ve positioned them coming from above as I love how the bulbs are nearly the same shape. The tape is only to hold it temporary as we will cover it with foam pads too.
  11. Attach each wire with tape on the back of the igloo and bend the wire towards the centre of the igloo. This can take a few attempts to get in place.
  12. Once secure, add foam pads to the back of the igloo, leaving a space for the wires in the middle.
  13. Post the battery pack through the hole in the background panel and make sure the igloo covers the hole and sits comfortably. You could add more snowy hills if you need to cover any gaps.
  14. Peel off the backing from the igloo and stick into position. Turn the whole square over and manipulate the wires (they’re quite long!) the sit flat on the back and position the battery pack in the bottom right corner (when looking at the card) but not to close to the edge.
  15. Add more tape to secure the wires and then cover the back with foam pads, apart from the battery pack.
  16. Peel off the backing paper and stick to the front of the card. Test out the button and glue the ‘PRESS HERE’ over the top.
  17. Curve each penguin on the wooden spoon handle and add a layer of foam pads to the back of them. Position them onto the card and add a second layer of foam to any part of them that’s not overlapping the igloo. Peel off the backing and stick them in place.
  18. Finish the card by adding the greeting to the bottom left corner, don’t add any glue behind the ‘S’ as this will float over the raised edge.
  19. Give to a loved one and mention, with great pride, that YOU made it especially for them.